To overcome this limitation, the authors designed and synthesized a lead-based metallomesogen, designated as PMM, that exhibits characteristic liquid-crystalline mesophase behavior combining solid-like order with liquid-like fluidity.
Single-junction and tandem solar cell architectures were fabricated through precisely controlled deposition procedures to assess the physical and electrical influence of the additive. The 0.8 molar Cs(FA)PbI3 perovskite precursor solution was prepared by dissolving caesium iodide, formamidinium iodide, dimethylamine hydroiodide, and lead(II) iodide in anhydrous N,N-dimethylformamide within an inert nitrogen glovebox. Transparent indium tin oxide glass substrates were pre-cleaned and modified with a magnetron-sputtered, 10-nanometer-thick nickel oxide-magnesium oxide layer, followed by a self-assembled hole-transport monolayer of [2-(3,6-dimethoxy-9H-carbazol-9-yl)ethyl]phosphonic acid deposited by spin-coating and thermal annealing at 100 degrees Celsius.
Deposition of the perovskite active layer proceeded through a two-step spin-coating protocol at 1,000 revolutions per minute for 5 seconds and 3,000 revolutions per minute for 30 seconds, followed by hotplate annealing at 170 degrees Celsius for 30 minutes to facilitate crystal formation. The target grain boundary modification was subsequently executed by spin-coating a 2 milligram per milliliter solution of PMM in chlorobenzene onto the annealed perovskite surface at 5,000 revolutions per minute for 30 seconds and annealing the layer at 110 degrees Celsius for 10 minutes. For transmission electron microscopy specimen preparation, thinner films were processed directly onto copper grids supported on conductive glass using precursor solutions and a lower metallomesogen concentration of 0.5 milligrams per milliliter.
To construct full two-terminal perovskite/silicon tandem devices, bottom cells were manufactured from n-doped, Czochralski-grown silicon wafers with submicrometer textured front surfaces. Intrinsic and doped hydrogenated amorphous silicon passivation layers and emitter contacts were deposited via plasma-enhanced chemical vapor deposition, completed by sputtered indium tin oxide and silver back contacts alongside a 10-nanometer sputtered indium tin oxide recombination junction. On top of the textured bottom cell, the hole-transport layer, 1.2 molar perovskite precursor, metallomesogen modifier, and a 20-nanometer evaporated buckminsterfullerene (C60) electron-selective contact were systematically assembled. Device completion involved atomic layer deposition of approximately 20 nanometers of tin oxide at 85 degrees Celsius, radiofrequency sputtering of a 44-nanometer indium zinc oxide front transparent electrode, thermal evaporation of silver contact grids, and deposition of a 130-nanometer magnesium fluoride antireflective coating.
Photovoltaic performance evaluated under simulated air mass 1.5 global illumination at 100 milliwatts per square centimeter revealed exceptional electrical output.
Beyond high initial power conversion efficiency, the engineered tandem devices demonstrated remarkable resistance to standard accelerated degradation stressors. Monolithic tandem cells protected by glass encapsulation with edge epoxy seals retained 95 percent of their initial operating efficiency after approximately 3,000 hours of continuous maximum power point tracking under one-sun equivalent light-emitting diode illumination. Furthermore, encapsulated devices exposed to rigorous damp-heat stress in an environmental chamber maintained at 85 degrees Celsius and 85 percent relative humidity retained 93 percent of their baseline efficiency after 1,500 hours of continuous environmental exposure.
The study provides critical experimental and theoretical evidence regarding mechanical strain distribution and grain boundary degradation mechanisms in methylammonium-free, pure-iodide perovskite materials.
Detailed encapsulation and degradation assessment protocols established the long-term endurance of both single-junction and tandem configurations under controlled operating stresses. For single-junction devices, encapsulation utilized a laminator operating at 100 degrees Celsius for 10 minutes to apply a polyolefin elastomer film, reinforced with butyl rubber edge seals as a moisture barrier. Full tandem assemblies had their front and back silver electrodes led out via conductive silver tape, were sandwiched between two cleaned glass sheets, and were sealed along the edges with epoxy inside nitrogen gloveboxes, allowing a full day for the sealant to dry. During continuous light-emitting diode maximum power point tracking, a multichannel measurement setup recorded electrical parameters using source meters with a current resolution of 1 microampere and a voltage resolution of 1 millivolt. Operating temperatures were monitored every two days by placing a thermometer adjacent to the active area without shading the device, allowing approximately five minutes to reach thermal steady state. Temperature-dependent tracking evaluated performance at 25, 53, 65, and 85 degrees Celsius, enabling researchers to determine degradation rates and extract activation energies from Arrhenius temperature dependence.
Thermal admittance spectroscopy, conducted with an LCR meter across frequencies ranging from 20 hertz to 100 kilohertz under an alternating-current voltage amplitude of 20 millivolts, mapped trap density of states and determined attempt-to-escape frequencies through customized temperature-controlled stages. Complementary drive-level capacitance profiling swept voltages from zero to open-circuit levels, applying variable alternating-current perturbations from 20 to 120 millivolts to profile carrier distributions and isolate deep trap densities from free carriers. In parallel, transient ion drift measurements conducted at 40 kilohertz captured capacitance transients over time to track ion migration dynamics. By fitting transient relaxation curves to exponential decay functions, the team quantified mobile ion concentrations, mobile ion diffusivities, and the corresponding activation energy barriers governing ion transport.
First-principles calculations employed the projector augmented plane-wave method within the Vienna ab initio simulation package, implementing the Perdew-Burke-Ernzerhof generalized gradient approximation and DFT-D3 dispersion corrections. Electronic wavefunctions were expanded with a 480-electronvolt plane-wave cutoff, while convergence criteria required electronic energies below 10^-5 electronvolts and residual forces on relaxed atoms below 0.05 electronvolts per angstrom. To prevent unphysical interactions between periodic slab replicas, simulations incorporated a 20-angstrom perpendicular vacuum gap.
Subject of Research: Perovskite/silicon tandem solar cell efficiency and stability enhancement via metallomesogen grain boundary engineering
Article Title: Grain boundary engineering using metallomesogen in formamidinium–caesium lead triiodide for stable perovskite/silicon tandem solar cells
Article References: Li, B., Wang, X., Wen, Y., Han, W., Ding, D., Wang, Y., Yu, X., & Yang, D. (2026). Grain boundary engineering using metallomesogen in formamidinium–caesium lead triiodide for stable perovskite/silicon tandem solar cells. Nature Energy. https://doi.org/10.1038/s41560-026-02161-z
Image Credits: AI Generated
DOI: 10.1038/s41560-026-02161-z
Keywords: Perovskite Solar Cells, Silicon Heterojunction, Tandem Solar Cells, Metallomesogen, Grain Boundary Engineering, Photovoltaics, Formamidinium Caesium Lead Triiodide, Wide-Bandgap Perovskite, Operational Stability, Defect Mitigation, Lattice Distortion, Power Conversion Efficiency, Maximum Power Point Tracking, Damp-Heat Stress, Shear Strain Relief, Semiconductor Physics
News Source: Denise Maddox. (November 21, 2026). Lead-Based Metallomesogen Stabilizes Perovskite-Silicon Tandem Cells Exceeding 32% Efficiency. Scienmag.



