The study, published in Advances in Aerodynamics, investigates how a commercial hydrophobic paint influences the turbulent flow structures around two representative models: the standard Ahmed body (SAB) and the elliptical Ahmed body (EAB). By comparing coated and uncoated versions of these models in a water tunnel, the team found that the coating modifies the slant separation bubble on the SAB, increasing its reattachment length by 80% and reducing shear stress, while having a comparatively minor impact on the fully separated flow of the EAB.
While hydrophobic coatings have been studied on simple geometries like spheres and cylinders, their effects on bluff bodies with intricate rear-end flow features have received limited attention. The authors note that such flow phenomena are critical in both academic research and industrial applications, including underwater energy harvesting and the design of submerged structures that experience significant resistance. The primary objective was to enhance the understanding of how surface treatments influence turbulent flow dynamics and separation, potentially leading to strategies for drag reduction and improved energy efficiency in engineering systems.
To conduct the experiments, the team utilized an open water tunnel with a test section measuring 6.00 meters in length, 0.60 meters in width, and 0.45 meters in depth. The models were constructed as quarter-scale versions of the 25-degree Ahmed body, with a height of 72 millimeters, using 3D printing with white polylactic acid (PLA). Two SABs and two EABs were produced, with one of each type coated with Ultra Ever Dry, a commercial hydrophobic paint. The coating was applied following supplier instructions, and its effectiveness was verified by measuring contact angles; water droplets on the untreated PLA surface had a contact angle of approximately 91 degrees, whereas the coated surfaces exhibited an angle of around 133 degrees, confirming the hydrophobic nature of the treatment.
The experimental setup employed both standard and time-resolved particle image velocimetry (PIV) to capture detailed velocity fields. The tests were carried out at a Reynolds number of 4.31 × 10⁴ based on the model height, with a freestream velocity of 0.60 m/s at a room temperature of 25 °C. The PIV system used a high-speed diode-pumped laser and CMOS cameras to acquire 48,000 images at a rate of 807 Hz for time-resolved measurements, as well as 9,000 pairs of images at 6 Hz for double-frame PIV. This dual approach allowed the researchers to compute both time-averaged statistics, such as mean velocity and Reynolds stresses, and time-dependent spectral statistics, providing a comprehensive view of the flow behavior.
For the standard Ahmed body, which features flow separation and reattachment at its slant surface, the hydrophobic coating produced distinct changes in the mean flow structure. In the uncoated SAB, the flow separates at the upper edge of the slant surface, forming a slant separation bubble (SSB) that reattaches at 62% of the slant length. With the coating applied, this SSB became longer and higher, extending the reattachment point to 80% of the slant length. This modification indicates a delay in the secondary separation process. Additionally, the wake recirculation length for the SAB decreased by 7.6% due to the coating, suggesting a reduction in the overall wake volume associated with the model.
The impact of the coating on the unsteady flow characteristics of the SAB was also significant. Frequency spectra analysis revealed that the dominant Strouhal number over the slant surface increased from 0.16 in the uncoated model to 0.24 in the coated version, representing a 33% increase. This shift is attributed to the modifications in the slant separation bubble, which alter the shedding patterns. Proper orthogonal decomposition (POD) analysis identified dominant Strouhal numbers of 0.36 and 0.48 for the first and second POD modes, respectively, in both coated and uncoated SABs, suggesting that the coherent structures in the wake were not significantly altered by the coating. However, dynamic mode decomposition (DMD) analysis identified a dominant Strouhal number of 0.30 in the wake of the coated SAB, compared to 0.27 for the uncoated model, aligning with the frequency spectra findings.
In contrast, the elliptical Ahmed body, which exhibits fully separated flow at the rear end, was less affected by the hydrophobic coating. The EAB lacks the slant separation bubble present in the SAB, resulting in a different baseline flow structure. The wake recirculation length for the EAB was reduced by only 6% with the coating, and the overall mean flow structure remained largely unchanged. A weak lower recirculation bubble was observed in the coated EAB, suggesting a minor effect on the underbody flow, but the primary separated shear layer from the upper edge of the slant surface was not significantly influenced. The Strouhal numbers over the slant surface of the coated EAB ranged from 0.40 to 0.55, while those in the wake varied from 0.25 to 0.85, indicating a nuanced effect on the unsteady flow characteristics.
Reynolds stress analysis further highlighted the differences between the two models. For the SAB, the coating reduced the peak values of streamwise Reynolds normal stresses (U’U’) from 0.12 and 0.09 in the uncoated model to 0.05 and 0.02 in the coated model. Similarly, the shear stress (U’W’) over the slant surface decreased from -0.017 to -0.008. These reductions suggest that the hydrophobic coating primarily affects the flow structure over the slant surface, reducing turbulence intensity and shear forces. For the EAB, the changes in Reynolds stresses were minimal, with only slight reductions observed in the underbody shear layer, reinforcing the conclusion that the coating has a limited impact on fully separated flows.
The study also examined the energy distribution among flow modes using POD. The relative energy captured in the first POD mode decreased for both the SAB and EAB with the coating, while the second POD mode energy increased for the EAB, indicating a redistribution of energy in the lower modes. For the SAB, the energy in the first mode dropped from 12.8% to 9.4%, while for the EAB, it decreased from 18.5% to 10.5%. The DMD analysis for the EAB revealed a very low dominant Strouhal number of 0.013, pointing to the presence of large-scale, energetic modes in the wake, which is consistent with the fully separated flow nature of this geometry.
The findings demonstrate that hydrophobic coatings affect the flow characteristics of 3D bluff bodies differently, depending on their inherent flow separation properties. The coating exerted a more pronounced influence on the SAB, characterized by separation and reattachment, compared to the EAB, which has fully separated flow. The observed changes, including the increase in reattachment length and reduction in shear stress for the SAB, suggest potential for drag reduction in such configurations. However, the authors note that further research is needed to optimize surface roughness and quantify drag effects more comprehensively. Future investigations should focus on the entire rear-end flow structure beyond the symmetry plane and explore how Reynolds number impacts the effectiveness of hydrophobic coatings in altering flow structures.
By leveraging a well-understood model like the Ahmed body, the study offers a foundational understanding that can be applied to real-world scenarios, including underwater systems and other practical applications. The results highlight the importance of considering the specific flow separation characteristics of a bluff body when evaluating the potential benefits of hydrophobic coatings for flow control and drag reduction.
Subject of Research: Experimental studies of the effects of hydrophobic coatings on flow separation around 3D bluff bodies
Article Title: Experimental studies of the effects of hydrophobic coatings on flow separation around 3D bluff bodies
Article References: Siddiqui, N. A., & Agelin-Chaab, M. (2025). Experimental studies of the effects of hydrophobic coatings on flow separation around 3D bluff bodies. Advances in Aerodynamics, 7(1), Article 23. https://doi.org/10.1186/s42774-025-00211-w
Image Credits: AI Generated
DOI: 10.1186/s42774-025-00211-w
Keywords: Experimental, studies, effects, hydrophobic, coatings, flow, separation, around, bluff, bodies, scientific research
News Source: Denise Maddox. (November 8, 2026). Hydrophobic Coatings Alter Flow Separation on 3D Bluff Bodies. Scienmag.



